Popular Science Appratus Workshops Private Limited

Specifications:

• The long and short sections of the teak wood beam are connected by hinge.
• Shear force measurement arrangement.
• Beam 1 mtr. span with supports.
• Weight set with loading hangers.
• Bending moment measurement arrangement .
• Spirit level to restore the loaded beam to original position.
• A spring balance with adjusting screw mounted at a fixed distance enables one to calculate the bending moment for any load position.
• This along with a spring balance and its adjustable screw is used for determining the shear force at the hinge section.

Range of experiments:

• Determination of shear force for different loading conditions.
• Determination of bending moment for different loading conditions.
• Influence line diagram for bending moment & shear force.
• The technical manual accompanies the unit.

Specifications:

• The compact bench top unit has a sturdy aluminum base plate, non-slip feet and central vertical pillar.
• Pivoting on this base is a ground steel plane which can be locked in any angular position between 45, indicated on a semi-circular protractor scale.
• Each tray in turn is attached to a weight hanger and weights are added until the tray just begins to slide.
• The slider trays also allow for additional weight to be added changing the experimental scope.
• Two composite slider trays are supplied.
• One pair being made out of aluminum and steel, whilst the other is made from nylon and brass.
• The hanger cord pulls the tray up the sloping steel plane whilst passing over a pulley and bearing.
• The bearing reducing friction to ensure accurate results.
• The experiment may also be used as an exercise in equilibrium of forces, determining the force required to move the tray along the plane giving the coefficient of friction.

Specifications:

• Material: Stainless Steel
• Weight set: 100 gm to 1 kg
• Horizontal arm : 75 cm
• Vertical arm: 20 cm
• Display: Analog
• Frequency: 50 Hz
• L type shape with horizontal graduated horizontal arm 75cm and vertical arm of 20cm.
• With a spring balance of 10 kg capacity to make the horizontal leg horizontal under any load.
• Complete with one sliding slotted set weight set 100gm to 1 kg.

Specification:

• The sliding mesh box, although it is still used on heavy commercial vehicles, is seldom found on modern cars, but its basic construction and operation are important from the students point of view as it represents the basic layout from which most modern gearboxes have been developed.
• The gearbox has been designed to represent a typical arrangement of a simple three forward ratio and reverse sliding mesh box.
• Gearbox consists of gear wheels of different sizes.
• The unit may be used for classroom demonstrations and by students in the laboratory.
• Pulleys fitted with protractors are attached to the input and output shafts so that the student may determine and verify velocity and torque ratios.
• The gearbox can be coupled to the Overdrive and Differential to represent a simple transmission system.

Specification:

• For determining the relationship between a load applied to a wire and the resulting extension.
• Consisting of an engraved brass scale with a vernier reading to 0.1mm.
• A tension weight, mass 1.3kg approx.
• A ceiling clamp is provided for the upper ends of the wires.
• with a pair of large wood screws for attaching it to a convenient overhead beam, door frame etc.
• Consists of a scale plate carrying a 0 to 30mm scale and a movable vernier readable to 0.1mm precision.
• Both have bars with clamping screws for the wires and hooks for the tension weight and loading masses.
• Complete with tension weight.

Features:

• A pipe section and various pressure measuring devices are fitted to a laboratory trolley with a demonstration panel, working area and cabinet.
• Various measuring containers are integrated into the pipe section.
• The sealed water circuit and pump with supply tank permit experiments to be performed independent of a mains water connection.
• Experimental apparatus are included in the cabinet, e.g. a device for determining the center of pressure of a column of water.
• This enables the pressure on a weir to be determined, amongst other aspects.

Specification:

• Submersible pump: 0.22kW
• Volumetric flow rate: 95Ltr/min
• Head: 12.5m
• U-Tube manometer: 0..500mmWC
• Two hydrometer jars: 450 x 50 mm.
• Hg U-tube manometer: 270..0..270mbar
• Aneroid barometer, range: 973 1047 mbar.
• Thermometer with a range between: -10 and 50oC.
• Pycnometer : 50 ml.
• Dimension: 1000-x800 x 1400 mm
• Weight: 120kg
• Archimedes module: displacement vessel, bucket and cylinder.
• Capillary tubes module with tubes of different size: 5 mm, 4 mm, 3 mm, 2.2 mm, 1.7 mm and 1.2 mm.
• Two falling sphere viscometer tubes: 300 x 40 mm, with marks at 0, 25, 175, 200 and 220.
• Set of stainless steel balls of different sizes: 3.175 mm, 2.381 mm and 1.588 mm
• Parallel plates capillary module.
• Variable scale lever balance to be used with the Archimedes module, up to 310 gr.

Descriptions:

• This is included in the form of a multiple tube manometer so that the pressure curve along the venturi flow meter can also be displayed.
• A hand pump facilitates pressurization of the manometers.
• Calibrating each flow meter using the volumetric measuring tank of the bench.
• Venturi meter, variable-area meter and orifice plate with flow-control valve.
• The apparatus is placed on the Hydraulics Bench; this provides the water supply to the unit.
• The bench is used as the source of water supply and for volumetrically calibrating each flow meter.
• Directly comparing flow measurement using a Venturi meter, variable area meter and orifice plate.
• The circuit and manometer are attached to a support framework, which stands on the working top of the Hydraulics Bench.
• Pressure tappings to measure head loss across each meter.
• Supplied with manometer board with eight tubes.

Specification:

• Manometer range: 0-400mm
• Throat diameter: 15mm
• Upstream pipe diameter: 31.75mm
• Upstream taper: 21 inclusive
• Downstream taper: 14 inclusive
• Dimension: 800-x800 x 1200 mm
• Weight: 120kg
• Number of manometer tubes: 8
• Orifice plate diameter: 20mm
• Variable area meter: 2-20 l/min

Description:

• A centrifugal pump and a flow control valve for adjusting the inlet pressure.
• The transparent operating area of the turbine enables an optimal view of water flow, rotor and guide vanes during operation.
• By adjusting the guide vanes the angle of attack, the cross-section and thus the output of the turbine are changed. An asynchronous machine is used as a generator for loading the turbine.
• The generator is equipped with a pendulum bearing and with a force sensor to determine the torque.
• A pump with variable speed via frequency converter provides for an energy efficient operation.
• The measured values are displayed digitally and can be processed further on a PC.
• The speed of the turbine is recorded by means of an inductive, non-contact position sensor at the generator shaft.
• The pressures at the inlet and outlet of the turbine, the temperature and the flow rate are recorded by sensors.

Specification:

• Hydraulic power: 2,1kW at 1500min-1
• Mechanical power: approx. 1,4kW at 1500min-1
• Rotor, D: 165mm
• 8 blades, 8 guide vanes
• Angle of attack adjustable: 023
• Centrifugal pump, multistage.

Variable speed:

• Pump head: 42m
• Tank: 550L
• Power consumption: 5,5kW
• Max. Flow rate:900L/min
• Asynchronous machine as generator
• Output: 2,2kW at 1440min-1

Measuring ranges:

• Temperature: 0100C
• Pressure (inlet): 1bar (turbine)
• Pressure (outlet): 06bar (turbine)
• Flow rate: 01000L/min
• Torque: 020Nm
• Speed: 03000min-1

Power supply:

• 02200W (generator)
• 400V, 50Hz, 3 phases
• 400V, 60Hz, 3 phases, 230V, 60Hz, 3 phases
• Dimension: 2350x1050x2050mm
• Weight: approx. 580kg

Specification:

• A real and operable air bag system is used to illustrate the structure of the system.
• In this way, the device demonstrates operation of the air bag system.
• Steering wheel can be safely removed and reinstalled during diagnosis or system testing.
• The training bench is made of advanced aluminum.
• Integrated SRS breakout box with test points for all terminals sized for standard meter leads.
• Manual fault box for SRS control module with 10 faults.
• Instead of using accumulators and requiring charging, the training panel connects to a 220V AC voltag which changes to a 12V DC voltage through the internal circuit.
• The 12V DC voltage protects the training panel against short circuit.
• Plastic plate, the color circuit diagram and working principal diagram are painted on the boards surface.
• The training panel is installed with a diagnosis socket, which can connect to automobile decoder to read fault codes reads and clears fault codes on the air bag system.
• Dimension: 1200 x 800 x 1400 mm
• Weight (approx.): 85kg

Specification:

• Displacement: 160cc
• Power: 6 HP
• Operated: Manually (Through a Crank Handle)
• Equipment Layout: On Base
• Dimension: 500 x 500 x 600 mm
• Weight: 35kg (approx)
• Sectioned for training purposes, professionally painted with different colours to better differentiate the various parts, cross-sections, lubricating circuits, fuel system, cooling system etc.
• It is specially made dissectible for demonstration purposes.
• It is provided with Flywheel and it is mounted on a sturdy iron frame.
• This actual cut section engine helps the student to understand about the parts and the working of the engine very easily.
• The actual cut section engine will be supplied with key card & very interesting literature regarding working.

Description:

• Heat transfer insulating powder trainer unit consists of two thin wall concentric copper spheres.
• The inner sphere houses the heating coil.
• Heating coil is made up of nichrome wire wound on mica sheet.
• The insulating powder packed between two shells.
• Four thermocouple are embedded on inner sphere and six thermocouples are embedded on outer sphere.
• The entire ten-temperature indicator, these reading enable of insulating powder.
• Power supply to the heater is given through a dimmer stat & is measured by voltmeter & an ammeter.
• Temperature can be measured with the help of thermocouples.
• Insulating powder Asbestos magnesia commercially available powder and Packed between the two spheres.

Specification:

• Radius of the inner copper sphere: 50mm
• Radius of the outer copper sphere: 100 mm
• Heater Mica Type
• Heating power: 350W
• Temperature limitation: 95C

Measuring ranges:

• Temperature: 2x 0325C
• Heating power: 0450W

Power Supply:

• 230V, 50Hz, 1 phase
• 230V, 60Hz, 1 phase; 120V, 60Hz, 1 phase

Specification:

• Water Tank: Made of Stainless Steel
• Rotating Arms: 9mm/6mm orifice diameter, Length 300 mm.
• Rota meter: 250 to 2500 LPH
• Electric Motor: Swinging field, Variable speed.
• Pump: FHP for water circulation.
• Dimension: 800 x 800 x 1200 mm
• Weight: 115kg
• Coriolis components of Acceleration can be determined at various speeds of rotation at water flow rates.
• The equipments is self contained, water re-circulating, provided with its own speed control unit and water-circulating pump.
• The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure.

Power Supply required:

• 230V, 50Hz, 1 phase
• 230V, 60Hz, 1 phase; 120V, 60Hz, 1 phase

Specification:

• Absorption refrigeration systems operate using thermal energy e.g. from industrial waste heat or from solar collectors.
• In small mobile systems, such as a camping refrigerator or minibar in a hotel, the required heat is generated electrically or by gas burner.
• This systems use the principle of liquids evaporating already at low temperatures when pressure is reduced.
• In process technology systems the resulting waste heat can be used for cooling.
• Working medium: ammonia-water solution
• Auxiliary gas: hydrogen
• Electric heater: 125W
• Evaporator heater, adjustable: 50W
• Dimension: 800 x 750 x 1200 mm
• Weight (approx.): 85 kg

Measuring ranges:

• Temperature: 4x -80180C
• Power: 0150W

Power Supply required:

• 230V, 50Hz, 1 phase
• 230V, 60Hz, 1 phase

• A bench-mounting base unit forms the main part of this set of products. 
• The dynamic tests run the input of the different drive units at a given speed using a motor, while measuring the input power. 
• Dynamometer loads the output of the drive unit while measuring the output power. 
• A variable-speed, low-voltage motor provides the shaft input turning force (effort) to the drive. 
• A dynamometer provides the output braking force (load) to the drive. 
• The dynamometer uses electromagnetic braking and a hysteresis effect to provide a variable load at a constant torque irrespective of the speed. 
• Sensors on the motor and dynamometer measure their shaft speed, torque and therefore power in and out at the drive. 
• Flexible couplings with collets connect the drive unit to the motor and dynamometer for quick and accurate alignment. 
• Students use the measurements to find the performance and efficiency of the drive unit.
• Axial trunnions with race bearings hold the motor and the dynamometer for free rotation against their load cell sensors to measure torque accurately.  
• Supplied with a three-shaft gear drive unit as standard, the base unit dynamically tests the gear drive and the other optional drive units. 

Specification:

• This mechanism is a differential gear train whose gears are all spur gears.
• The mechanism is driven and both wheels are releasing free, all spur gears are running.
• The function of this mechanism is similar to the previous differential gear train.
• It is basically a combination of two planetary gear trains on which the two sun gears are coaxial.
• The right wheel is held, the right sun gear will become fixed but the other gears are still rotatable; when the left wheel is held, the left sun gear will become fixed but the other gears are still rotatable.
• This mechanism is applicable for the situation that requires two controllable inputs.

Specification:

• The cutaway models represent original components in which the active parts are clearly visible to the user while fully maintaining their mechanical functionality.
• The planetary gear is a special type of gear drive, in which the multiple planet gears revolve around a centrally arranged sun gear.
• The planet gears are mounted on a planet carrier and engage positively in an internally toothed ring gear.
• Torque and power are distributed among several planet gears.
• Each of the cutaway models is securely mounted on a base plate.
• Sun gear, planet carrier and ring gear may either be driving, driven or fixed.
• Planetary gears are used in automotive construction and shipbuilding.
• Which also has handles to allow them to be carried. They are powered by hand.
• Dimension: 450 x 400 x 300 mm (approx)
• Weight: 10kg(approx)

Description:

• The model will be mounted on to a tubular frame.
• All the hardwares and gears will be suitably electroplated.
• Suitable color imported painting will be carried out along with Miracle coating for the model will be done for extra gloss and shine.
• Operated: Manually(a Crank Handle)
• Equipment Layout: On Base

Specification:

• Rack type steering box.
• Hydraulic pump.
• Oil tank with relevant filter.
• Connecting pipes.
• Dimension: 1000 x 600 x 550 mm
• Weight: 25kg (approx.)

Specification:

• Operated: Manually
• Equipment Layout: On Base with wheel
• Light metal construction.
• Operated manually by a crank handle.
• Mounted on a base.
• Dimension: 350 x 400 x 300 mm
• Weight (approx.): 7 kg
• The rotor (triangular piston), operates by the driving shaft and rotates inside the stator clearly showing the different phases.
• The compression phase, a small bulb lights up to simulate the gas ignition.
• This cut-away model is carefully sectioned for training purposes and is professionally painted with different colors to better differentiate the various parts, cross sections and fuel system.
• Cross-sectioned various parts to show internal operation.

Specification:

• The trainer can be used in the classroom environment for demonstrations to students.
• The training brake rig can be used as visual aid for students of mechanical subjects to demonstrate and explain the structure and components.
• Also, automotive training stand can be used as a educational equipment for the brake system repair and service procedures.
• Demonstrates full functionality of a 4-wheel hydraulic brake system.
• Provides easy access to all brake components without the confinements of a real vehicle.
• Pressure gauges show actual braking pressure at each wheel.
• Real automotive components with fully functional disc/drum hydraulic braking system including:
• Fits through a standard 30 door opening.
• Heavy duty metal stand with casters for easy transport.
• Parking brake components.
• All hydraulic components.
• Brake pedal and parking brake pedal.
• Power brake booster.
• Hydraulic pressure gauges at each wheel.
• Fully functional parking brake system.
• Dimensions: 1000 x 800 x 1200 mm
• Weight: 140 kg (approx)

Feature:

• The system has a hand crank.
• Constructed with heavy duty metal and plastic.
• Unit is open system to study and sandwiched by two clear plastic plates.
• Nice bench top or desktop item.
• Operated: Manually
• Equipment Layout: On Base

Specification:

• Has 2 Dials to show rotation.
• Nice bench top or desk top item.
• Dimension: 400 x 200 x 300 mm
• Weight: 5kg
• Constructed with heavy duty metal and plastic.
• Unit is open system to study and sandwiched by two clear plastic plates.
• This demonstration shows the fundamentals of how a internal Gear and Pinion drive works.

Specification:

• It consists of a stationary cylinder, a roller and a shaft.
• The shaft has an eccentric on which the roller is mounted.
• A blade is set into the slot of a cylinder in such a manner that it always maintains contacts with a sloter by means of a spring.
• The blade moves in and out of the slot to follow the rotor when it rotates.
• The blade separates the suction and discharge parts, therefore it is often called a sealing blade.
• When the shaft rotates, the roller also rotates the roller rotates so that it always touches the cylinder wall.
• Dimension: 500 x 400 x 500 mm (approx)
• Weight: 35 kg (approx)

Features:

• All the pressure taps are connected to a manometer with a water collector (water might be pressurized).
• The ends of the conduits are removable, enabling to be placed in either convergent or divergent form with respect to the stream direction.
• For the operation, the module is placed on the Hydraulics bench top It has adjustable legs for leveling.
• Adjusting the control valve located at the end of the module can modify the flow rate and the pressure in the module.
• A flexible hose attached to the outlet pipe is directed to the volumetric measuring tank.
• The inlet pipe ends in a female coupling, which may be directly connected to the bench supply.
• There is also a probe (Pitots tube) moving along the conduit or measuring the height in every section (dynamic pressure).

Specification

• Narrowing:Downstream: 21.
• Upstream: 10.
• Manometer range: 0 to 300 mm of water.
• Number of manometer tubes: 8.
• Upstream diameter of the throat: 25 mm.
• Dimensions: 800 x 450 x 700 mm. approx.
• Weight: 15 Kg. approx. (33 pounds approx.)
• Anodized aluminum/ MS powder coated structure and panel of painted steel.

Features:

• Steam engine model ideal for classroom demonstrations
• Cross-sectioned cylinder to show internal operation
• Working parts piston, slide valve both move and the link motion and reversing method operate.
• This cutaway model is carefully sectioned for training purposes, professionally painted with different colours to better differentiate the various parts, cross-sections, lubricating circuits, fuel system, cooling system etc.
• Many parts have been chromium-plated and galvanized for a longer life.

Specification:

• Dimension: 450 x 350 x 300 mm (approx)
• Weight: 9 kg (approx)
• This model shows the internal structure and operating principles of a working steam engine.
• The metal cylinder is cross-section cut and is covered with a clear plate to show movement of the piston inside the cylinder.
• Complete with working parts: the piston, slide valve both move and the link motion and reversing method can be observed.
• The movement of the wheel is light enough to demonstrate even by blowing air.

Features:

• Available in 1100C and 1400C temperature.
• Programmable temperature controller.
• Rugged construction for long run.
• Fitted with safety devices.
• Uniform heating rate.

Specification:

• Max temperature: 1100C, 1400C
• Continuous operating temp.: 1000C, 1300C
• Heating wire: Silicon carbide (Sic) rods
• Thermocouple: K Type, R Type
• Exterior MOC: Mild steel powder coated
• Insulation: Ceramic fiber blanket
• Temperature controller: PID controller with SCR power control
• Chamber MOC: Ceramic fiber board, Ceramic Zirconium board
• Power supply: 220 Volts 50Hz, 3 Phase 440 Volts 50Hz

Dimensions And Capacity:

• 300 x 300 x 457mm, 42 liters volume
• 300 x 300 x 609 mm, 56 liters volume

• The experiment module includes all the essential parts to allow students to create process control systems. 
• The main part is the process vessel, with a stirrer, a temperature sensor, level and pressure sensors, a heat exchanger and vent valve.
• It also includes sockets and a built-in computer interface. 
• It also includes two loops, linked by the heat exchanger in the process vessel. 
• One loop is the heating loop with pump, heater tank and heater. 
• The other loop is a process and cooling loop with pump, cooler, fan, valves and reservoir. 
• The control module links to the experiment module to provide access to the connections of each part on the experiment module. 
• It includes a clear mimic diagram with switches and controls to allow manual control of pump speed, cooler-fan speed, heater power and stirrer.

• Boring diameter: 65 140 mm, 80 165 mm
• Max. boring depth: 300 mm, 400 mm
• Spindle speed: 250, 380 r/min
• Spindle feed: 0.11 mm/r, 0.12 mm/r
• Spindle quick reset: 636 mm/sec
• Overall dimensions: 320x330x850 mm
• Machine weight: 62 kg, 85 kg

Descriptions:

• Cylinders manufactured out of quality steel.
• Cylinder Bores will be honed to mirror finish or long life of piston seals.
• All chevron seals & bronze strip used for leak proof performance.
• Surface ground hardened for long life of seals & corrosion resistance.
• Capacity in tones: 5 -200
• Pressure: 25 mpa
• Table travel: 200 - 270 mm
• Motor H.P: 2 - 10
• Bed size: 235x235 - 750x800

Specifications:

• Upper electrode is actuated by foot lever or by air cylinder.
• The electrode force can easily be calculated in both systems.
• The 63KVA AC metal spot welding machine is electric resistance projection welders with an asymmetrical body design. The automatic welding equipment is used for welding iron, copper, aluminum, stainless steel, and other materials.
• By tap method with 8 tap adjustments on primary of the main transformer having current control from 50% to 100% in 8 steps.
• Air system is provided with gauge and manual system with calibrated spring.
• All air accessories such as filter, lubricator, regulator, gauge, solenoid valve and speed valve are incorporated.
• By tap link method with 8 tap adjustments on primary of the main transformer having current control Electrodes, Electrode holders, Arms, Transformer are all water cooled with one single water-cooling circuit.

Features:

• Easy to use and service.
• Offering water cooled grinding.
• Easy to progress and change abrasive rolls.
• Reliable and robust design.
• The machine is manufactured from Stainless steel with a cast aluminum base.
• Hard anodized rollers with paper support plates for long life of the machine.

Specification:

• Cooling rinse system:Water
• Dimension: 565x 535 x 200 mm
• Weight: 25kg
• Grinding stations: 240, 360, 600, 800 and 1200 grit silicon carbide rolls
• Roll sizes: 3-7/16-inch width x 60 feet length with 1 -inch core
• Construction:Aluminum casting and stainless steel, Hard coat anodized rollers and paper support plates

Features:

• Single point pivot on engine mounting enables accurate thrust measurement.
• No need for external lubrication system.
• No need for external battery and charger.
• Fully tested for high performance and safety.
• Tough, transparent polycarbonate safety screen.
• An optional floor-standing frame is available to house the unit together with its fuel tank and electronic console.
• The engine has been integrated into a sturdy metal frame that holds it firmly, while enabling accurate measurement of the thrust produced by the engine.
• An electronic preprogrammed controller constantly supervises the engine, ensuring safe operating conditions at all times.
• The engine inlet has been replaced with a custom fabricated frontal duct, to enable the air mass flow rate to be accurately measured.

Specification:

• Thrust: 200N typical
• Mass flow: 450 g/s
• Ignition system: Glow plug
• Engine rpm: 105,000rpm typical
• Engine mount: Single pivot point
• Dimension: 880 x 510 x 1185 mm
• Weight: 150 kg (approx)
• Exhaust gas temperature: 800C typical
• Compressor type: Single-stage radial
• Turbine type: Single-stage, low-mass axial flow

Features:

• A hydraulic automatic transmission consists of the following parts: torque converter, planetary gear set, clutches and bands, and hydraulic and lubricating oil.
• Colors are used to differentiate between parts.
• Many parts have been chromium plated and galvanized for a longer life.
• The model is made out of full size original used automatic transmission of a car.
• The automatic shifting of the gears can be explained using this model clearly.
• Transmission will be suitably sectioned to show the internal details, of gear mechanism of forward and reverse speeds.
• The model will be mounted on to a tubular frame.
• Suitable color imported painting will be carried out along with Miracle coating for the model will be done for extra gloss and shine.
• All the hardwares and gears will be suitably electroplated.

Specification:

• Hydraulic torque converter.
• Multiple-plate clutches.
• Control valves.
• Epicycloid gear change with 5 forward speeds plus reverse.
• Operated manually by hand crank applied on the torque converter.
• Mounted on stand with wheels.
• Dimension: 750 x 550 x 700 mm (approx)
• Weight: 110kg (approx.)

Description:

• Transparent process tank makes it possible to clearly observe the evaporation process at the heated cylinder.
• The cylinder is used as a model to demonstrate a fire tube heated from the inside.
• The special liquid used evaporates at low temperatures.
• Sensors provide all relevant data.
• An integrated water-cooled condenser allows for a continuous boiling process.
• The measured values are indicated on digital displays and can also be transmitted directly to a PC via USB.

Specification:

• Heater Power: 250W, continuously adjustable
• Surface area: 0,001875m
• Diameter: 80mm
• Tank: 10L
• Surface area: 0,0578m
• Cooler, copper coil
• Safety valve opens at 2,2bar

Measuring ranges:

• Pressure: 04bar absolute
• Flow rate: 0,051,8L/min
• Temperature thermocouple: 0200C
• PowerSupply: 230V, 50/60Hz, 1 phase, 120V, 60Hz/CSA, 1 phase
• Dimension: 900x450x820mm (approx)
• Weight: 60kg(approx)

• This is a compact industrial slant bed lathe with 8 station programmable turret.
• Its design replicates industrial machine features such as cast iron bed, precision grade grounded ball screws, LM guide ways, servo motors, coolant system, AC panel cooler for control box, full machine guard, etc.
• Chuck Capacity mm: 100
• Maximum Turning Diameter mm: 80
• Maximum Turning Length mm: 190
• Positioning Accuracy mm: 0.01
• Hole Through Spindle mm: 20
• Spindle Speed Range RPM: 150-4000
• Spindle Motor KW: 3.7
• No. of StationsNos.: 8
• X/Z Axis Travelmm: 95/210
• Rapid X/Z mm/min: 5000
• Feed Rate mm/min: 0-5000
• Tailstock Base Stroke mm: 170
• Stroke mm: 40
• Diameter mm: 35

• Power Source: 200-240VAC, 50-60Hz, 3- Phase
• Controlled axis : 3-axis
• Simultaneously controllable axis : 3-axis
• High Response Velocity (HRV)
• Part program storage : 512kbyte
• Registerable programs : 200
• Operation panel : 10.4 color LCD
• I/O interface : RS-232C Interface

Capacity:

• X-axis-travel (longitudinal movement of table): 500 mm
• Y-axis travel (cross movement of saddle): 400 mm
• Z-axis travel (vertical movement of spindle head) : 300 mm

Table:

• Working space (X-axis x Y-axis) : (650mm X 400mm)
• Capacity of workpiece mass : 300kg (uniform load)
• Working surface configuration : (3xT-slots size 14 mm pitch 125 mm)

Feedrate:

• Rapid traverse rate : 48 m/min (X,Y,Z)
• Feedrate : 30000 mm/min
• Machine height: 2236 mm
• Floor space: 1615 mm X 2040 mm
• Mass of machine: Approx. 2000 kg

Accessories:

• Automatic oil lubricating system.
• Working lamp.
• Air blow for chips
• Signal Lamp (3 color)
• Tool Holder locking device
• Tool Setting Stand
• Touch probe.
• 200VAC +10 to -15% 3-phase, 50Hz +/- 16kVA
• Tool length switch for automatic measurement.
• LED illumination.
• Coolant unit with chip flush.

• Universal milling machine is preferred for producing a vast variety of surfaces that may be a part of piece or serial production.
• The procedure of milling is carried out by making use of different types of milling cutters like cylindrical disc, end cutters, angular milling cutters, etc.
• As a result, this milling machine is able to accommodate surfaces that are horizontal, vertical, helical, groovy, fissure, and angular.
• Surface of Table (MM): 800175
• No. of T-Slots: 3
• Size of T-Slots:
• Swivel either Side of Table: 45
• Cross Traverse (MM): 150
• Vertical Traverse (MM): 400
• Diameter (MM): 25.4
• No. of Spindle Speed: 6
• Main Motor Power (HP): 1, 1.5, 2
• Weight (Kgs.): 450
• Range of Spindle Speed (RPM): 40
• Spindle Diameter (MM): 50 - 90
• Longitudinal Traverse (MM): 475 - 675
• No of Feed in Longitudinal Table Long.: 2

• Drilling capacity (mm): 65
• Drilling capacity in Cast- IRON: 70
• Tapping in steel: 50
• Spindle travel (mm): 300
• Height of Box Table: 400
• Height of the Base Plate: 210
• Range of Power Feed: 0-115
• Optional Feed: 0.13-1.10
• Column Diameter (mm): 330
• No. of spindle speed : 9/50-805 rpm
• Horz. Move. Of Radial Arm (mm): 660
• Working surface of table (mm): 560 x 460
• Drilling Head motor (HP/RPM): 5/1440
• Elevator Motor (HP/RPM): 3/1440
• Base plate dimension (L x W): 2050 x 990
• Total Height of the Machine : 2440 (Approx)
• Working surface of base plate (mm): 1400850
• Horizontal Movement of Drilling Head: 1000
• Max / Min Dist. Spindle Nose to Base plate: 1120/460
• Max / Min Dist. Spindle center to Col. Center: 1700/700

Specification:

• Provides consistent boring.
• Durable and reliable tool.
• Accuracy in making hole.
• Can drill maximum of 25 mm.
• Creates less noise and less vibration.
• Requires less or low maintenance but provides excellent machining performance.

Technical Specifications:

• Machine Capacity (mm): 25 mm
• Column Dia. (mm): 92 mm
• Table Travel: 480 mm
• Spindle Travel (mm): 250 mm
• Main Electrical Motor: 1 H. P.
• No. of Spindle Speed: 8
• Table Size (mm): 330 x 330 mm
• Center of Spindle to column (mm): 250 mm
• Distance Spindle to Table (mm): 645 mm, 660 mm
• Distance Spindle to Base (mm): 1000 mm, 1045 mm
• Distance from Spindle Centre to (mm): 250 max
• Base Sie (Machined Area) (mm): 255 x 310 mm
• Overall Height with guard (mm): 1780 mm
• Range of Spindle speed (RPM): 70-2000, 130-2600

Features:-

• The frame is of all steel construction, fabricated from rolled steel plates with suitable cross ribbings.
• Presses up to 30T will be supplied with C.I. legs. Proper alignment of the frame is ensured by machining.
• The Crank shaft is made of special alloy steel with precisely machined to grind finish having closed accuracy
• Fitted in bronze bushes for smooth working, longer life with consistent performance.
• Flywheel is made of high grade cast iron.
• Gears are of steel cast or fabricated.
• Gear teeth are generated by precision hobbing machine.

Technical Specifications:

• Capacity in Tons (mm): 5 - 50
• Crankshaft Diameter (mm): 70 - 140
• Adjustment of Stroke (mm): 38 - 89
• Adjustment of Ram (mm): 25
• Punch Hole in Ram (mm): 25 - 45
• Hole in Bed (mm): 63 - 95
• H.P. : 1 - 5
• Bed Thickness (mm): 50 - 83
• Flywheel Dia. (mm): 406 - 660
• Strokes per minute (mm): 80 - 35
• Dist. between bed to Ram (mm): 177 - 350
• Bed Size (Length x Width) (mm): 355178
• Floor To Top of Bed (mm): 700 - 100